Coolant Hose, 1/2" ID, 25/32" OD, 10' Length, 2-1/2" Bend Radius, 125PSI
(Pack of
1)
• EPDM tube and cover
• Reinforced with single wire helix, two-ply synthetic fabric for pressure or vacuum service
• Resistant to heat, mild oil, chemicals, ozone and abrasion
• Extremely flexible and light weight
• Temperature range: –30°F to +240°F (–34°C to +115°C)
• Ideal marine utility hose (non-oily environment) – meets or exceeds USCG requirements for marine wet exhaust
• Useful in wastewater, industrial, construction and agricultural applications
Hold hose firmly and cut straight through to contact with spring steel wire. Do not cut wire.
Pull both ends apart about three inches to expose wire.
Grasp end to be used and snip wire slightly with wire cutters inside the end to be used. This cut should be close enough so that wire end does not protrude.
To install hose, twist slightly when placing over fitting. Apply to both fittings before clamping. We recommend the use of screw-type clamps. Do not use self-tightening clamps.
Frequently Bought Together
Brass Fuel Line Male Pipe Elbow 90° 3/8"
Couldn't load pickup availability
Silicone Heater and Radiator Hose 1-5/16" OD
Couldn't load pickup availability
Silicone Heater and Radiator Hose 1-1/2" OD
Couldn't load pickup availability
Miniature Clamp SS 5/16 to 7/8"
Couldn't load pickup availability
DOT Connector Male Brass 1/4 x 1/8-27
Couldn't load pickup availability
Hose Clamp 301 SS 3/4 to 1-3/4"
Couldn't load pickup availability
Non-Perforated Clamp 316 SS #8 5/8 to 15/16"
Couldn't load pickup availability
Hose Clamp 301 SS 2-1/16 to 3"
Couldn't load pickup availability
Constant Torque Hose Clamp SS 1-3/4 to 2-5/8"
Couldn't load pickup availability
DOT Swivel Elbow Male 360° Brass 3/8 x 1/4-18
Couldn't load pickup availability
Ball Check Grease Fitting Straight
Couldn't load pickup availability
Super 77 Hose Clamp SS 5/8 to 1-1/4"
Couldn't load pickup availability
IFI 100/107 Top Locknut Grade C 5/8-11
Couldn't load pickup availability
SAE Flat Washer Thru-Hardened Steel 1/4"
Couldn't load pickup availability
Hex Nut Grade 8 Alloy Steel 3/8-16
Couldn't load pickup availability
Product Description
• EPDM tube and cover• Reinforced with single wire helix, two-ply synthetic fabric for pressure or vacuum service
• Resistant to heat, mild oil, chemicals, ozone and abrasion
• Extremely flexible and light weight
• Temperature range: –30°F to +240°F (–34°C to +115°C)
• Ideal marine utility hose (non-oily environment) – meets or exceeds USCG requirements for marine wet exhaust
• Useful in wastewater, industrial, construction and agricultural applications
Hold hose firmly and cut straight through to contact with spring steel wire. Do not cut wire.
Pull both ends apart about three inches to expose wire.
Grasp end to be used and snip wire slightly with wire cutters inside the end to be used. This cut should be close enough so that wire end does not protrude.
To install hose, twist slightly when placing over fitting. Apply to both fittings before clamping. We recommend the use of screw-type clamps. Do not use self-tightening clamps.
Technical Specifications
| Item#: | 99675 |
|---|---|
| Type | Coolant Hose |
| I.D. | 1/2 " |
| Hose O.D. | 25/32 " |
| Bend Radius | 2-1/2 " |
| Working Pressure | 125 PSI |
| Burst Pressure | 500 PSI |
| Length | 10 ft |
| Recommended Hose Clamp | 86724 |
| Description | To be Discontinued - No volume |
| UNSPSC #: | 25170000 |
| TAA Compliant: | Yes |
| Weight: | 3.0 lb |
Product Restrictions
