Coolant Hose, 1/2" ID, 25/32" OD, 10' Length, 2-1/2" Bend Radius, 125PSI
(Pack of
1)
• EPDM tube and cover
• Reinforced with single wire helix, two-ply synthetic fabric for pressure or vacuum service
• Resistant to heat, mild oil, chemicals, ozone and abrasion
• Extremely flexible and light weight
• Temperature range: –30°F to +240°F (–34°C to +115°C)
• Ideal marine utility hose (non-oily environment) – meets or exceeds USCG requirements for marine wet exhaust
• Useful in wastewater, industrial, construction and agricultural applications
Hold hose firmly and cut straight through to contact with spring steel wire. Do not cut wire.
Pull both ends apart about three inches to expose wire.
Grasp end to be used and snip wire slightly with wire cutters inside the end to be used. This cut should be close enough so that wire end does not protrude.
To install hose, twist slightly when placing over fitting. Apply to both fittings before clamping. We recommend the use of screw-type clamps. Do not use self-tightening clamps.
Couldn't load pickup availability
California Proposition 65: Not Applicable
www.P65Warnings.ca.gov
Frequently Bought Together
Silicone Heater and Radiator Hose 2-15/16" OD
Couldn't load pickup availability
Windshield Wiper Hose 3/32" ID x 50'
Couldn't load pickup availability
Hose to Pipe Nipple Straight 5/8" x 1/2-14
Couldn't load pickup availability
Constant Torque Hose Clamp SS 2-1/4 to 3-1/8"
Couldn't load pickup availability
Ball Check Grease Fitting 90°
Couldn't load pickup availability
DOT Compression Union Brass 1/4"
Couldn't load pickup availability
Super 77 Hose Clamp SS 1-1/4 to 2-1/8"
Couldn't load pickup availability
Non-Perforated Clamp 316 SS #10 3/4 to 1-1/8"
Couldn't load pickup availability
Super 77 Hose Clamp SS 1-1/2 to 2-3/8"
Couldn't load pickup availability
Hose Clamp 301 SS 9/16 to 1-1/4"
Couldn't load pickup availability
Pipe Coupling Brass 1/2-14 x 1/2-14
Couldn't load pickup availability
DOT Connector Male Brass 3/8 x 1/4-18
Couldn't load pickup availability
Locknut with Nylon Insert Grade 8 5/16-18
Couldn't load pickup availability
SAE Flat Washer Thru-Hardened Steel 5/16"
Couldn't load pickup availability
SAE J995C Locknut with Nylon Insert Grade 8 1/2-13
Couldn't load pickup availability
Product Description
• EPDM tube and cover• Reinforced with single wire helix, two-ply synthetic fabric for pressure or vacuum service
• Resistant to heat, mild oil, chemicals, ozone and abrasion
• Extremely flexible and light weight
• Temperature range: –30°F to +240°F (–34°C to +115°C)
• Ideal marine utility hose (non-oily environment) – meets or exceeds USCG requirements for marine wet exhaust
• Useful in wastewater, industrial, construction and agricultural applications
Hold hose firmly and cut straight through to contact with spring steel wire. Do not cut wire.
Pull both ends apart about three inches to expose wire.
Grasp end to be used and snip wire slightly with wire cutters inside the end to be used. This cut should be close enough so that wire end does not protrude.
To install hose, twist slightly when placing over fitting. Apply to both fittings before clamping. We recommend the use of screw-type clamps. Do not use self-tightening clamps.
Technical Specifications
| Item#: | 99675 |
|---|---|
| Type | Coolant Hose |
| I.D. | 1/2 " |
| Hose O.D. | 25/32 " |
| Bend Radius | 2-1/2 " |
| Working Pressure | 125 PSI |
| Burst Pressure | 500 PSI |
| Length | 10 ft |
| Recommended Hose Clamp | 86724 |
| Description | To be Discontinued - No volume |
| UNSPSC #: | 25170000 |
| TAA Compliant: | Yes |
| Weight: | 3.0 lb |
Product Restrictions
California Proposition 65: Not Applicable
www.P65Warnings.ca.gov
