Expansion Shield Anchor, 7/8" Drill Size, 1/2"
(Pack of
5)
• Evenly distributed four-way expansion of anchor wall by internal nut
• Excellent holding power in concrete, brick, stone and cinder block
• Corrosion-resistant, non-deteriorating zinc alloy casting bends and conforms without fracturing
• Meets GSA Specification FF-S-325 3.2.2.2.1.3
• Use for anchoring medium and heavy loads in solid and hollow-base materials
• Typical applications: Guard rails, fascia, equipment hangers, straps, conduit, overhead plumbing installations and suspended heating and air conditioning ductwork
1. Drill hole to at least shield length.
2. Clean hole with air or wet swab.
3. Place Forway® Expansion Shield in the hole.
4. Position fixture or equipment.
5. Insert screw or bolt through equipment into shield and tighten.
NOTE: Screws not included.
Forway® is a registered trademark of U.S.E. Diamond, Inc.
Tensile strength, shear strength and tensile block values shown; a 4:1 safety factor is recommended.
Couldn't load pickup availability
California Proposition 65: Not Applicable
www.P65Warnings.ca.gov
Catalog page#: 6-31
Frequently Bought Together
Masonry Anchor Hex Washer Head Steel 3/16 x 1-1/4"
Couldn't load pickup availability
Wedge Type Stud Bolt Anchor Steel 1/2 x 4-1/4"
Couldn't load pickup availability
Masonry Anchor Hex Washer Head Steel 1/4 x 1-3/4"
Couldn't load pickup availability
Pin Drive Expansion Anchor Steel 3/8 x 5"
Couldn't load pickup availability
Pin Drive Expansion Anchor Steel 1/2 x 6"
Couldn't load pickup availability
Pin Drive Expansion Anchor Steel 5/8 x 4"
Couldn't load pickup availability
Flat Washer Grade 12 Thru-Hardened Steel M8
Couldn't load pickup availability
SAE J995C Locknut with Nylon Insert Grade 8 3/8-16
Couldn't load pickup availability
PTO Pin Lock 1/4 x 2-1/2"
Couldn't load pickup availability
Waterproof Work Aqua Light 66 LED
Couldn't load pickup availability
Butt Connector 22 to 18 AWG Clear
Couldn't load pickup availability
USS Flat Washer Thru-Hardened Steel 1/4"
Couldn't load pickup availability
Product Description
• Evenly distributed four-way expansion of anchor wall by internal nut• Excellent holding power in concrete, brick, stone and cinder block
• Corrosion-resistant, non-deteriorating zinc alloy casting bends and conforms without fracturing
• Meets GSA Specification FF-S-325 3.2.2.2.1.3
• Use for anchoring medium and heavy loads in solid and hollow-base materials
• Typical applications: Guard rails, fascia, equipment hangers, straps, conduit, overhead plumbing installations and suspended heating and air conditioning ductwork
1. Drill hole to at least shield length.
2. Clean hole with air or wet swab.
3. Place Forway® Expansion Shield in the hole.
4. Position fixture or equipment.
5. Insert screw or bolt through equipment into shield and tighten.
NOTE: Screws not included.
Forway® is a registered trademark of U.S.E. Diamond, Inc.
Tensile strength, shear strength and tensile block values shown; a 4:1 safety factor is recommended.
Technical Specifications
| Item#: | 96961 |
|---|---|
| Anchor Size | 1/2 " |
| Type | Forway Expansion Shield Anchor |
| Drill Size | 7/8 " |
| 3,000 PSI Concrete Shear Strength | 8,100 lb |
| Tensile Block | 3,050 lb |
| Thread Pitch | 13 |
| 3,000 PSI Concrete Tensile Strength | 5,100 lb |
| UNSPSC #: | 31162101 |
| TAA Compliant: | Yes |
| Weight: | 0.8 lb |
Product Restrictions
California Proposition 65: Not Applicable
www.P65Warnings.ca.gov
